11/30/2022 0 Comments Teamviewer online![]()
This feature puts the entire device into a special sleep mode. Please understand that Modern Standby is a Microsoft feature which TeamViewer has no control over. You should also find that these times correspond to the settings you have on the device for either the "Turn off the display" value, or else the hidden "Console lock display off" value which I discussed in my previous post above.įor example, if your "Turn off the display" setting is set to 10 minutes, and you stop using your Surface at 15:10, you will probably notice that the display turns off, and TeamViewer goes offline, at around 15:20, and you'll see a corresponding entry in your log file at 15:20 which says "Service::CheckModernStandb圜hange: entering modern standby". #Teamviewer online Offline#You can also search within your own log files for the phrase Service::CheckModernStandb圜hange and you should see entries that say either "entering modern standby" or "leaving modern standby", and these entries should correspond with the times that TeamViewer goes offline or online. #Teamviewer online pro#This is evident from the TeamViewer log files I've seen from Surface devices, including the Surface Pro 3 I'm using. There is no doubt in my mind that when TeamViewer on the Surface Pro is going offline, it is because the Surface is entering Modern Standby mode. I've spent a bit more time digging deeper into this. #Teamviewer online install#Otherwise, after i install the teamviewer's display driver, i can not change the display light level by power setting. If teamviewer go offline while my program still online, i think this is a problem, not a feature. but teamviewer as a remote controller and tool, as i configure keep network, the teamviewer should keep online, if teamviewer's remote display need display turn on, use some tricks to do so. So i think, though this is a feature to save power. If i send mouse_event move message, the display will turn on, and teamviewer back online. When the display turn off after 1 minute, teamviewer go offline, but my program keep alive online, i can communicate with it. I write a program run in background, wait for remote command through network.Ģ. I think teamviewer should fix this problem.īecause i use win10 tablet pc, i want to save power, so set display turn off after 1 minute, system keep alive always, network keep alive always.ġ. So why is this only an issue for Teamviewer service? 'Īlso it would be nice to have screen go black to save energy.įurthermore.I have services installed that I CAN access. This behavior just suddently started some days ago. Maybe this a solution, but I also doubt that this is the whole story, since this was never an issue earlier. This was never a problem and teamviewer stayed connected the whole day. But I don't think that this is causing the issue as I usually close the lid of my surface book, which switches off the display aswell. #Teamviewer online update#If you set it to 0, then the Surface's display will turn off after the amount of time specified in the Turn off the display setting in the Control Panel's Power Options - usually this is 10 minutes.Īs to why this seems to have changed within the past few days - my guess is that a recent update from Microsoft may have changed this behaviour on these wrote: Now that this setting is no longer hidden, you can change it to something longer, or else set it to 0 which disables it completely. In summary, if you carefully follow the instructions there (and bearing in mind that editing the Registry is risky business), you'll end up with a new Display setting called Console lock display off timeout, which is located in the Advanced Power Settings in the Control Panel. This previously-hidden setting causes Windows to turn off the display (by default) 60 seconds after it's locked, and on a Surface tablet this means it enters Modern Standby mode. Rather than repeat the instructions, I'll point you to the article that contains the solution, and give credit where credit's due: #Teamviewer online windows 10#According to my research, this is caused by a setting in Windows 10 which is hidden by default, but which you can unhide and change with a simple edit to the Windows Registry. So the issue here is why the screen is turning off after the Surface is locked. You can learn more about the Windows 10 Modern Standby feature in this video from Microsoft.) As a result, programs like TeamViewer are not able to stay connected. (The fact that TeamViewer goes offline is expected behaviour. When the Surface's display turns off, it enters Modern Standby mode, which is a new and more advanced sleep state. Specifically, when I lock the device, the screen will turn off after about 40-60 seconds, and the device will go offline on my TeamViewer Computers & Contacts list. I've noticed this happening on my own Surface Pro 3 as well. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |